您现在的位置是:网站首页> 内容页

[BlueZ] 1、Download install and use the BlueZ and hcitool on PI 3B+

  • t900bet国际手机版
  • 2019-06-10
  • 23人已阅读
简介星期日,02.九月201811:58下午-beautifulzzzz1.IntroductionBluezisthedefaultBluetoothprotoc

星期日, 02. 九月 2018 11:58下午 - beautifulzzzz

1. Introduction

Bluez is the default Bluetooth protocol stack on Linux. It should be present and installed on your Linux distribution. If not, building and installing from source is not too difficult:

Download the latest stable source release of Bluez from here. Unzip the compressed file you downloaded.Install the headers and libraries required for Bluez compilation:

2. Download And Install

I follow the blog (Installing Bluez 5.44 onto Raspbian?) to install bluez-5.50.

Download the most recent version from the official page:http://www.bluez.org/download/.

For example, at the time of writing it was 5.50, so I used(on my pi):

wget http://www.kernel.org/pub/linux/bluetooth/bluez-5.50.tar.xz

Then I extracted it and built it:

tar -xf bluez-5.50.tar.xzcd bluez-5.50

Read the README! It lists the dependencies and the configure switches:

Install the dependencies first: (glib, dbus, libdbus, udev, etc.)

sudo apt install libdbus-1-dev libudev-dev libical-dev libreadline-dev

note: If you do not install the libdbus-1-dev, you will later get this strange error:

configure: error: D-Bus >= 1.6 is required

once you"ve installed dependencies, you can configure switches:

./configure --prefix=/usr --mandir=/usr/share/man --sysconfdir=/etc --localstatedir=/var --enable-experimental

then do:

makesudo make install

It takes maybe 10 minutes to compile. After installing, you should find bluetoothd in /usr/libexec/bluetooth. You should also see bluetoothd in /usr/lib/bluetooth.

Go to each of these directories and type

./bluetoothd --version

You"ll note that the one in libexec is new and the one in lib is old.

In order to make sure that d-bus is talking to you new BlueZ 5.50 and not your old BlueZ 5.43, you need to tell systemd to use the new bluetooth daemon:

sudo vim /lib/systemd/system/bluetooth.service

Make sure the exec.start line points to your new daemon in /usr/libexec/bluetooth.

For me, that wasn"t enough. No matter what, upon restart I always got bluetoothd 5.43... So I just created a symlink from the old one to the new.

First rename the old file:

sudo mv /usr/lib/bluetooth/bluetoothd /usr/lib/bluetooth/bluetoothd-543.orig

Create the symlink:

sudo ln -s /usr/libexec/bluetooth/bluetoothd /usr/lib/bluetooth/bluetoothdsudo systemctl daemon-reload

That should do it.

3. How to use the bluez and hcitool

3.1 setup bluetooth service

Start the bluetooth service and enable automatic startup, assuming you"re using systemd as the init daemon:

sudo systemctl start bluetooth.servicesudo systemctl enable bluetooth.service

3.2 hcitool scan for bluetooth devices

Before start scanning make sure that your bluetooth device is turned on and not blocked, you can check that with the rfkill command:

sudo rfkill list

If the bluetooth device is blocked (soft or hard blocked), unblock it with the rfkill command again:

sudo rfkill unblock bluetooth

Bring up the bluetooth device with hciconfig command and start scanning, make sure the target device"s bluetooth is on and It"s discoverable:

sudo hciconfig hci0 uphcitool scan

Wait few moment to complete the hcitool scan or hcitool lescan, the results will be something like bellow:

Here 00:1A:7D:DA:71:0A is the bluetooth MAC address and SHEN-PC is the name of the bluetooth device, i.e. an PC.

note: use hcitool lescan will forever scan ble devices, if use ctrl+c stop it, it will show error(ref to LINKS 4 to solve):

hcitool lescanSet scan parameters failed: Input/output error

3.3 bluetooth service discovery

Now we have the bluetooth MAC address of the target device, use the sdptool command to know which services (like DUN, Handsfree audio) are available on that target device.

sdptool browse 28:ED:6A:A0:26:B7

You can also use the interactive bluetoothctl tool for this purpose.

If the target device is present, you can ping it with l2ping command, requires root privilege:

➜ bluez-5.50 sudo l2ping 94:87:E0:B3:AC:6FPing: 94:87:E0:B3:AC:6F from B8:27:EB:8E:CC:51 (data size 44) ...44 bytes from 94:87:E0:B3:AC:6F id 0 time 53.94ms44 bytes from 94:87:E0:B3:AC:6F id 1 time 77.12ms44 bytes from 94:87:E0:B3:AC:6F id 2 time 38.63ms44 bytes from 94:87:E0:B3:AC:6F id 3 time 46.13ms44 bytes from 94:87:E0:B3:AC:6F id 4 time 59.96ms5 sent, 5 received, 0% loss

So, bluetooth service discovery is useful to determine the type of the device, like if it"s a bluetooth mp3 player or it"s a keyboard.

LINKS

1.Bluetooth on Modern Linux by Szymon Janc2.dbus-python tutorial3.Linux bluetooth setup with bluez and hcitool4.hcitool lescan shows I/O error

@beautifulzzzz智能硬件、物联网,热爱技术,关注产品博客:http://blog.beautifulzzzz.com园友交流群:414948975

文章评论

Top